Instruments
Product Categories
Resources
Part #
To protect the interior of the instrument, this collection chamber catches fluid in the event of an internal leak.
Part #
This assembly shows if the packing has started to leak.
Part #
The RF41 Synthetic Grease w/PTFE is a non-toxic lubricant used to assist in creating a seal between the RF34 Viton® Gasket and the module/bottle, and between the PTFE coated septa and the septa port on the bottle. For application instructions...
Part #
Along with a 3 ft Extension Cable ( Part #: RF44 ), the Dual Lead Rechargeable Battery Pack ( Part #: RF46 ) provides the capability to charge your RF1 module's battery during an experiment by keeping it connected to the Battery Charger ( Part #...
Part #
This is the internal computer that controls the XT15/XT15I Fat Extractor.
Part #
The LCD Screen Assembly is used in the XT10 and XT15 Fat Extractors, the HCl Hydrolysis System, and the DELTA & A2000 Fiber Instruments. Mounted on the front of the instrument, this LCD screen displays temperature, time, and other functions during an...
Part #
DE1 contains 125 grams of Diatomaceous Earth, which is often used to improve the filtration process. Click the link below for the DE1 SDS information.
Part #
Before ordering an XT10/XT10I Extractor Vessel, contact our Technical Services Department to confirm your instrument configuration.
Part #
This part is used to filter solvent vapors and should be replaced every 3 months or after 100 instrument operations. This part is only used in the XT15/XT15I instruments.
Part #
Before ordering an XT15/XT15I Extractor Vessel, contact our Technical Services Department to confirm your instrument configuration.
Part #
The nitrogen check valve prevents fluid back-up from the 12 IDF/SDF delivery lines into the pneumatic lines.
Part #
This is a chemical container used for supplying 95% EtOH to the instrument.
Part #
Before the final weighing step in a Dietary Fiber analysis, the bags must be dried. The TDF50 stainless steel Bag Drying Rack has twelve positions for holding a full set of IDF/SDF bags when drying them in an oven.
Part #
This container is used with the AOAC 2009.01/2011.25 methods.
Part #
This clamp bar is used in the SDF part of the instrument to close the Filter Bag just above the filter.
Part #
This is the controller with display used in the 120v RD Dryer.
Part #
This dual voltage fan drives air through the Daisy Incubator (D200/D200I) to maintain consistent heat.
Part #
The RF45 and RF45X Programmed RF Chips w/antenna facilitate communication between the Gas Production Modules, the Module Zero, and the Gas Production Base Coordinator.
Part #
The RF2X Base Coordinator facilitates communication between the Gas Production Modules ( RF1X / RF5X ) and the GPM Software installed on a PC. One RF2X Base Coordinator services an RFS base kit of up to 50 modules. To purchase, please contact ANKOM...
Part #
The Glass Tip with O-ring is a part of the analog level sensing system in the DELTA/DELTAI, A2000/A2000I Fiber instruments. Found in the Fiber Optic Cable & Glass Tip assembly ( Part #: A32 ), it is used to detect and regulate the fill level within...
Part #
ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7057 bottle provides the following features: - up to 1000ml of space to hold analysis material - a protective coating...
Part #
ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7126 bottle provides the following features: - up to 100ml of space to hold analysis material - an Amber tint to...
Part #
ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7127 bottle provides the following features: - up to 250ml of space to hold analysis material - an Amber tint to...
Part #
ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7130 bottle provides the following features: - up to 250ml of space to hold analysis material - a protective coating...
Part #
ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7132 bottle provides the following features: - up to 1000ml of space to hold analysis material - a protective coating...
Part #
The 7147 Male Luer Cap is used to close off the end of the Female Luer Port ( Part #: 7146 ) or the Luer Duckbill Check Valve ( Part #: 7139 ).
Part #
The Copper Water Supply is used to connect the DELTA/DELTAI and A2000/A2000I instruments to the user's water source.
Part #
The Tubing Seal, 3x8 mm is used within the RF1X module to secure and seal the Pressure Sensor ( Part #: RF31 ) and Viton-Silicone Tube ( Part #: RF11 ) into their respective ports in the bottom of the module housing.
Part #
Used for globe vent valve. Located inside the cabinet left side panel.
Part #
This kit and the accompanying process guide provide the parts and instructions to complete the Preventative Maintenance (PM) process for the standard ANKOM XT15/XT15I Fat Extractor. This should be completed annually for an instrument used daily or...
Part #
This kit and the accompanying process guide provide the parts and instructions to complete the Preventative Maintenance (PM) process for the high penetration ANKOM XT10 Fat Extractor. This should be completed annually for an instrument used daily or...
Part #
For use in the ANKOM FLEX Analyte Extractor. High Strength PTFE magnetic stir-bar; used in each assembled digestion vessel for more difficult to mix samples.
Part #
This 120/220 volt supply provides the correct power to the instrument electronics.
Part #
At various times during assays involving ANKOM instruments, you will need to seal the ANKOM Filter Bags. The HS Heat Sealer (120v 50/60HZ) is used for sealing ANKOM Filter Bags. The sealer dimensions are: 13.5"L x 4"W x 8"H
Part #
Replacement cover for the 120v and 220v Heat Sealers (Part #: HS , HSi ). This is applied over the heating element and held in place with clamp strips. For an installation diagram, refer to the Heat Sealer Operation Manual.
Part #
The Temperature Probe w/ ground terminal is used in the DELTA/DELTAI and A2000/A2000I Fiber instruments. This probe provides an accurate vessel temperature which is displayed on the Ascon controller.
Part #
The Lid Assembly is used on the DELTA/DELTAI and A2000/A2000I Fiber instruments and seals the top of the digestion vessel.
Part #
This assembly heats the digestion vessel in the 220v A200I instrument.
Part #
The Outer Exhaust Hose Assembly is used in the DELTA/DELTAI and A200/A200I Fiber instruments. It drains waste solutions from the digestion vessel.
Part #
The Bag Suspender Rod w/ Nut Assembly is used when damage to the rod or pitting has occurred. It runs through the middle of the bag suspender and holds the nine trays in place and is used in the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber...
Part #
The Bag Weigh Holder is used to hold a filter bag open for easy insertion of the sample. This part is especially useful during the weighing process.
Part #
F1N is reagent grade 1N Sulfuric Acid. The product comes in 1 Liter Bottles and is sold in quantities of 4. *Special handling is required for International Shipments
Part #
The Hinge Block Assembly is found in the A200/A200I Fiber Instruments. The assembly includes a shoulder bolt and is used to secured the lid to the vessel during sample digestion.
Part #
This hose carries waste from the vessel to the outer exhaust hose. Includes hose with clips.
Part #
Order F58 Filter Bags by 100 count package quantity (e.g. 10 = 1,000 filter bags). Volume discounts will be applied when added to the shopping cart. Quantity discounts apply at 1000, and 5000 quantities. The F58 filter bag is mainly designed for...
Part #
This assembly heats the digestion vessel in the 120v instrument.