Part #
Power Supply B is a transformer that supplies 25v DC power to the solenoid valves and paddle heaters. This comes with an in-line fuse kit for overload protection and is used for both 110v and 220v instruments.
Part #
This 15 amp fuse is used on the DELTA, A2000, and A200, Fiber instruments (120v). It helps protect the instrument from a possible power surge.
Part #
During digestion, the jars ride on this belt to prevent them from slipping.
Part #
The fluid supply distribution manifold directs input fluids to the six IDF/SDF stations. To replace the supply manifold in your instrument, follow TDF Service Procedure Supply Manifold Replacement (TS029).
Part #
The Mixing Pad Assembly may require replacement if bent or if the pad has become loose. Refer to TDF Service Procedure Mixing Pad Adjustment (TS010) to ensure proper alignment.
Part #
This is an enzyme container used for supplying Amylase to the instrument.
Part #
The largest contributor to poor TDF results is the effect of static electricity on the weighing process. The TDF52 Bag Weigh Holder is used during the weighing process to eliminate static electricity while the bag is being weighed.
Part #
The Helical Coupler is used on the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber instruments. It couples the agitator shaft with the motor to provide sample agitation within the vessel. For the A200/A200I instruments, refer to Service Procedure...
Part #
This container is used with the AOAC 2009.01/2011.25 methods.
Part #
The Vacuum Sensor Assembly monitors pressures on the supply lines and is used to identify empty containers, plugged fluid lines, or damage to a supply line. For replacement instructions, refer to Service Procedure Vacuum Sensor Installation (TS013).
Part #
Replacement tube set for all seven pinch valves [Enzymes, IDF inlet(2), SDF Inlet(2) and Waste(2)]. Refer to Service Procedure Tube Replacement (Pinch Valves) (TS005) for installation instructions.
Part #
This clamp bar is used in the IDF part of the instrument to close the top of the Filter Bag.
Part #
This clamp bar is used in the SDF part of the instrument to close the top of the Filter Bag.
Part #
This assembly heats the Extraction Chamber of the 120v HCl instrument.
Part #
The H33 Bag Holder is used to hold the bags in the HCl Extraction Chamber during as assay. This assembly holds 20 bags. Can also be used in the RD/RDI Dryers.
Part #
Attaches on the top of the RD/RDI Dryer. This filter is used when drying filter bags after a hydrolysis operation is done with an ANKOM HCl/HCI Hydrolysis System.
Part #
This resettable breaker is used to protect the instrument against power surges that are out-of-specification.
Part #
The durable Viton™ Gasket increases the seal quality between the RF1 Gas Production Module and the glass bottle. We recommend replacing gaskets when they become worn, torn, or begin to leak. The RF34 pack includes 10 Viton™ Gaskets. For installation...
Part #
The TDF Pressure Sensor Assembly monitors the pressures of the six fluid lines and is used to identify weaknesses in tubing downstream of the peristaltic pump. Refer to TDF Service Procedure Pressure Sensor Replacement (TS011) for installation...
Part #
The ETS Snap Disc Thermostat is used in the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber instruments. It interrupts power to the heating element in an over-temperature condition.
Part #
This assembly includes a probe that provides an accurate temperature to the Athena controller.
Part #
Replacement fused filter plug and on/off switch.
Part #
This assembly connects the pressure switch to the digestion vessel.
Part #
Used in both the XT10/XT10I and XT15/XT15I. This metal screen filters particles and should be cleaned regularly. XT15 Service Procedure Instrument and Components Cleaning (X5S017) provides instructions for accessing this part.
Part #
The Paddle Bar Replacement Kits includes the Paddle Bar Assembly and the tools required for its installation. The Paddle Bar functions as both a paddle mixer and heater with embedded sensors to allow for independent heat regulation at each position...
Part #
This tool is used to view the spray tips for obstructions during cleaning and maintenance.
Part #
The EPDM Tubing is the replacement tube for the HCl / Acetic Acid supply lines. Refer to Service Procedure Tube Replacement (Supply Line) (TS007) for installation instructions.
Part #
Wire brush for cleaning the bottom of the XT10/XT10I and XT15/XT15I vessel. If fat residues burn to the bottom of the vessel, this tool, when used with a drill, will assist with cleaning.
Part #
Used in both XT10/XT10I and XT15/XT15I. The X78 Flow Control Assembly is used to visually indicate that water is flowing through the reflux circuit during the reflux cycle. Once the solvent has reached extraction temperature, the reflux circuit will...
Part #
This harness provides power to, and communication from, the pressure sensors.
Part #
This PTFE washer is used to seal the brass solvent filter to prevent leaks in the XT10/XT10I and XT15/XT15I.
Part #
This assembly includes the silicone exhaust tube for the RF system.
Part #
Stainless Steel Tray with Spring Clamps for holding flasks from 100 to 1000ml (includes spring clamps). Works with Shaker baths WB20ISH and WB20SH .
Part #
These balls are used on top of the water bath to help maintain temperature. The balls are hollow in order to minimize condensation that can negatively impact the electronics in the RF1 modules.
Part #
The XT Solvent Drain Valve Assembly is used in the XT15/XT15I and XT10/XT10I Fat extractors. Its function is to maintain pressure in the vessel within certain limits during the run and to drain the vessel at the end of the run.
Part #
This O-Ring Kit includes parts that do not swell when contacting high penetrating solvents. This kit is no longer available. However, the components of the X95 kit can be ordered individually as parts #5663 and # 5806 .
Part #
The valve seat is attached to the end of the valve piston within the solenoid supply valve used on the XT10/XT10I, XT15/XT15I, HCl/HClI, DELTA/DELTAI, A2000/A2000I, and TDF/TDFI instruments.
Part #
Used in the XT15/XT15I Instrument. This kit includes replacement pistons for the four solvent valves (Q4, Q5, Q6, and Q7).
Part #
This Viton™ O-ring is used within the solenoid supply valves on the XT10/XT10I, XT15/XT15I, HCl/HClI, DELTA/DELTAI, A2000/A2000I, and TDF/TDFI instruments for proper sealing and replaces the valve body seal O-ring around the inside of the valve guide...
Part #
This larger 4 liter chemical container is used for supplying buffer to the instrument. The larger size accommodates 8 runs on the instrument before refilling is necessary.
Part #
This drive belt connects the motor and the drive roller ( Part #: 834 ).
Part #
The MUX-T board communicates temperature signals to the main controller and is critical in paddle and in-line heat control.
Part #
The ANKOM Positive Control Capsule Set was developed to simplify the validation test of your RF Gas Production System and provide a positive control curve for comparison within each experiment. The validation test familiarizes the user with the system and ensures the system and all the modules are functioning properly. ANKOM recommends running a validation test at least once per quarter by adding one BLUE capsule, one CLEAR capsule, along with 100ml of distilled water, to each RF1 bottle. For detailed instructions about running a validation test, see ANKOM RF Service Procedure RS004.
Part #
The Water Regulator Assembly is found in the DELTA/DELTAI Fiber instruments and helps maintain the appropriate water pressure for rinses and manifold flushing.