Resource Center

This kit includes replacement pistons for the two solvent valves (Q5 and Q6).

The TDF107 Synthetic Grease, 10 gm, is a non-toxic lubricant used to minimize friction within the peristaltic pump, thereby extending the life of peristaltic pump tubing. For application instructions, see TDF Service Procedure Long Life Pump Tube...

This is the programmed touchscreen hardware used in the human interface module. This part can be purchased to replace an existing touchscreen that may be damaged in some way.

This circuit board contains the electronics that control the instrument.

The Mixer Flow Control Valve Assembly allows for better control and easier adjustment to the intensity of sample mixing to help ensure proper digestion.

The Internal Drain Hose Assembly with check valves delivers necessary chemicals for each assay. Included in the assembly are tubes that drain chemicals after their use.

Located in #FLEX30 Slide Valve and #FLEX32 Vent Valve assemblies Rev A.

Replacement Vent Bottle & Tube Assembly for XT15/XT15I. This includes SS tube with compression fitting, bottle cap, 500ml coated glass bottle, and 6 ft. of chemical resistant tubing.

This kit and the accompanying process guide provide the parts and the instructions to complete the Preventative Maintenance (PM) process for the DELTA or A2000 Automated Fiber Analyzers. This procedure should be completed annually for an instrument...

This Extraction Vessel seal should be used when running Pet Ether in your XT10/XT10I and XT15/XT15I.

The Thermal Cut-off Assembly is used in the heater for the oven. It consists of a non-resettable thermal fuse that shuts down power to the heater if the temperature exceeds 240°C.

The Vent Valve Assembly functions to release pressure from the vessels during vessel fill and saponification.

This part displays the solvent level on the XT15/XT15I instruments.

Belt 808 rides on this roller.

This relay replaces Part #: 6114 and controls power to the Ascon temperature controller, motor, and drain valve on the DELTA/DELTAI and A2000/A2000I Fiber instruments, as well as the HCl/HClI instrument.

This container can be used for storing solvents when not in use. When the instrument is properly configured, a cubitainer can also be used for automatically dispensing solvents during an assay. The CUBITAINER® is a disposable flexible package. It can...

This one-way valve is used for adding gas into the glass bottle of an RF1 module. This is often done to purge the bottle of existing gases. To push gas into the bottle using an Air Purge Assembly ( Part #: RF28 ), see RF Service Procedure Purge...

The RF2 Base Coordinator uses an antenna to communicate with the RF1 modules. The 7143 antenna is a replacement part for the one connected to the RF2 Base Coordinator, and/or the one connected to the RF29 Antenna Extension Assembly.

The Black Nitrogen Supply Tubing is used as a replacement part for cracked or damaged nitrogen supply tubing or where additional length is required. The unit price is per foot. Please specify the length in the quantity field when ordered.

This is the internal computer that controls the A2000 Fiber Analyzers.

The A10 Motor Assembly 220v drives the agitation system in the 220v DELTAI & A2000I.

Valve A or B dispense the correct detergent into the digestion vessel. Refer to A2000 Service Procedure A and B Valve Cleaning (AS004) for instructions.

The valve opens to vent the vessel during the fill and drain processes. Refer to Service Procedure Water and Vent Valve Service (AS016) for further information.

This probe provides an accurate temperature to the Athena controller.

This motor turns the jars during digestion.

The Bag Suspender w/ Weight is used within the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber instruments. It is the entire array that holds the filter bags in the vessel and ensures proper circulation of solutions and uniform digestion of the samples.

This switch turns the heat to the digestion vessel on and off.

The Packing Set is used in the DELTA/DELTAI, A200/A200I, and A2000/A2000I Fiber instruments. Its purpose is to create a seal and keep the solution from leaking from the vessel into the interior cabinet. This includes two lengths of graphite rope...

This assembly includes the handle and clamping device used for sealing the lid and hinge block assembly to the vessel.

This motor agitates the bag suspender at the proper RPM in the 120v instrument.

This corrosion-resistant PEEK valve body and stainless piston is the mechanical component of the Buffer supply valve as of November 2022. It is used as a replacement component for the Water, Buffer, EtOH78, and EtOH95 supply valves. It includes the...

Used in both the XT10/XT10I and XT15/XT15I. This valve spring is for the Q5 solvent valve only. This spring should not be used in any other valve.

This module cap includes a notch that allows for a battery extension cable.

This container is used to hold the Buffer for TDF CODEX methods.

The Low Pressure Sensor Assembly is used to monitor nitrogen (N2) line pressure in two locations. One marked 43 monitors N2 going to the four round bottom flasks used for solvent evaporation. One marked 45 monitors N2 Low Pressure and is displayed on...

The High Pressure Sensor Assembly is used to monitor the main nitrogen input line pressure to the instrument.

The FLEX21 Thermistor Assemblies are used to monitor temperature at eight locations. One is used to monitor the vessels' temperatures and is marked 46. One is used to monitor the reference temperature surrounding the round bottom flasks and is marked...

Belt 808 rides on this roller.

The RF Gen 3 Circuit Board contains the electronics used for communication with all RF1X / RF5X modules.

The RF Solenoid assembly is used to replace a faulty solenoid pinch valve within the RF1 or RF1X Module.

The FLEX Maintenance Kit provides the essential items needed to keep your FLEX Analyte Extractor operating smoohtly. The following items are included: 4 - Container Filters ( Part #: 8202 ) 4 - Vessel Top O-Ring ( Part #: 9231 ) 4 - Column top O-Ring...

This tube replacement set is used as part of preventative maintenance and includes pre-cut, bagged, and labeled lengths of silicone tubing (3/16”OD x 1/16”ID) used in the delivery of reagents in the ANKOM TDF Dietary Fiber Analyzer.

Used in older XT15/XT15I. Please contact ANKOM for more information.

The DELTA01 Maintenance Alert Assembly is used in the DELTA and A2000 instruments. It includes the Drip Tray w/plugged drain hole ( Part #: 692 ), Agitator Apron ( Part #: 638.7 ), and brass washer and functions as a collector for a fluid leak...

Pneumatic Control Solenoid Valve used in TDF and FLEX Instruments. Replacement part for a faulty Solenoid Valve.

This relay monitors the heaters in the following ANKOM instruments: XT15, XT10, HCl. DELTA, and A2000.

This 10amp fuse is used in 120v AC input to the HCl, XT10, XT15, and in both TDF and TDFI on the DC output lines from the power supply. Used to protect against power surges.

This probe is used to measure the temperature within the Extraction Chamber of the HCl instrument.

Ideally, you want to remove as much acid as possible from samples before drying them. When using the blotter, you can remove a maximum amount of acid from the samples after completing the HCl extraction, and before drying in the dryer.